RolandoHow man
San-RamonInsta
EscazuFresh frStep of cold storage design: selection and laying of cold storage thermal insulation materials. The use of cold storage thermal insulation materials must be adjusted to the time, which not only has excellent fire resistance, but also has high cost performance. There are several types of cold storage insulation materials. One is the plate produced and processed into a fixed shape and specification, with fixed length, and the raw materials can be sprayed into the brick or concrete warehouse of the cold storage to be built immediately. After shaping 12cm or 15cm thick cold storage board is generally used for ultra-low temperature cold storage and freeze-cleaning cold storage; Another kind of cold storage can be sprayed with polyurethane spray paint and polyurethane foam, it is both waterproof and thermal insulation. Thermal insulation materials include polyurethane, polystyrene grease, etc. Polyurethane is non hygroscopic and has good fire resistance, but the cost is high; Polystyrene resin has strong water absorption capacity and weak fire resistance, but the cost is low.
Indirect cooling is that the air in the warehouse is pumped into the air cooling device by the blower. The air is absorbed by the evaporation pipe circling in the cooling device, and then sent to the warehouse for cooling. The advantages of air cooling are rapid cooling, uniform temperature in the warehouse, and can bring harmful gases such as carbon oxide out of the warehouse during storage.
Rolando.The exhaust temperature of the compressor in the fresh-keeping warehouse can be read out from the thermometer on the exhaust pipeline. It is related to the adiabatic index, compression ratio and suction temperature of refrigerant. The higher the suction temperature, the greater the compression ratio, the higher the exhaust temperature, and vice versa.
If there is more air or refrigerant oil in the evaporator, the heat transfer effect will be reduced: once more refrigerant oil is attached to the inner surface of the evaporator heat transfer tube, the heat transfer coefficient will be reduced. Similarly, if there is more air in the heat transfer tube, the heat exchange area of the evaporator will be reduced, the heat transfer efficiency will be significantly reduced, and the decline rate of warehouse temperature will be slowed down.
.Different food processing technical processes for the construction of cold storage are combined with local urban planning. The construction of cold storage is the design requirements and construction of cold storage, which not only avoids the cross pollution between foods, but also ensures its transportation facilities: within the construction scope, a reasonable overall layout, saves land and reduces costs.
On the basis of cold storage and preservation, the quick-frozen warehouse increases the regulation of gas composition, inhibits the respiration of fruits and vegetables, delays their metabolic process, controlled atmosphere storage of fruits can prolong the storage period by 2 & mdash; Three times or more. OK and prolongs the storage period and shelf life of fruits and vegetables. Generally, what is the standard of quick freezing warehouse?
The overall construction achievements of the cold storage project have been put into use, and the service life can reach 10 years.
The product shade warehouse is a warehouse location below 20 ℃ and the sun cannot be straight. The humidity is 45% ~ 75% relative humidity, and there are corresponding strict requirements for the wall, ceiling, ventilation, disinfection and epidemic prevention of the warehouse. The refrigeration system adopts full-automatic microcomputer electrical technology and does not need to be on duty. It mainly stores western and Chinese grass materials and instruments, and can monitor and record the temperature and humidity in the storage area.
Evaporator is not only an exchanger for refrigeration and bulk cooling, but also a very important one. Its task is bulk cooling. It is mainly used for refrigeration and heat absorption in fresh-keeping warehouse. In the long-term work of the fresh-keeping warehouse, the fins of the evaporator will also be covered with dirt, mostly pasted with some sundries of the products. It is specialized in products and renewable resources. Its business includes: cold storage installation, cold storage installation, cold storage construction, fruit fresh-keeping cold storage medical cold storage. In addition, but reaching a certain thickness will have an impact on the cooling of the fresh-keeping warehouse, If the refrigeration of the fresh-keeping warehouse becomes poor, it should be cleaned with a special cleaning agent for the evaporator.
Fire retardant, flame retardant and high temperature resistant polyurethane is a kind of flame retardant self extinguishing material after adding flame retardant. Its softening point can reach more than 250 ℃, and it will decompose only at higher temperature. In addition, polyurethane forms carbon deposits on the surface of the foam, which helps to isolate the foam below. It can effectively prevent flame spread.
device management.During the cold storage commissioning, special personnel shall be assigned to ensure that the surface of the cold storage plate shall reflect evenly without condensation and cold running; Sealing conditions of joints and holes; Whether the warehouse door and delivery port are not tightly sealed, and timely deal with the problems of insulation and seal failure such as degumming and air leakage.
There are many application scenarios of cold storage, which are different. For a long time, it provides various cold storage installation,RolandoHow much is it to install a small cold storage, cold storage installation, cold storage construction,RolandoDesign and installation principle of cold storage, fruit preservation cold storage, medical cold storage, on-site settlement, and has offices all over the country for long-term cooperation. Different purposes, functions and designs,RolandoPrice of one square meter for cold storage installation, so what needs to be understood in cold storage design?
Energy saving and power saving: the design cost of quick freezing warehouse mentioned above is very low, but it has a great impact on the cost of quick freezing warehouse and later use cost. The electricity bill is often an important expenditure item in the later stage. The design scheme of the show can greatly reduce the power consumption of the quick freezing warehouse. The selection of the back sunny side of the quick freezing warehouse, the selection of the thickness of the thermal insulation board should be appropriate the tightness of the quick freezing warehouse door, and the temperature difference between the adjacent cold storage rooms should not be too large are all issues that we need to consider. There are also some tips, we can that the ground insulation of medium-sized cold storage is more complex than that of small cold storage, and the ground insulation operation of large cold storage with larger warehouse area will be more complex. The common operations are as follows: first lay the ventilation pipe to prevent the ground from freezing drum cracking, then lay the XPS extruded plate (staggered laying is required when laying the extruded plate), then lay the moisture-proof and vapor barrier on the upper and lower sides of the extruded plate, then pour the reinforced concrete (generally at least 15cm thick), and then make the emery floor or epoxy floor according to the requirements. Among them, the XPS extruded plate is also laid according to the warehouse temperature. For example, the XPS extruded plate with thickness of 150 ~ 200mm needs to be laid in the general low-temperature cold storage, while the XPS extruded plate with thickness of 100 ~ 150mm can be laid in the high-temperature cold storage.
Test conclusion.Cold storage is fireproof, flame retardant and high resistance. Professional cold storage installation, cold storage installation, cold storage construction, fruit preservation cold storage medical cold storage and other special products, price advantage and guaranteed quality. Polyurethane is a flame retardant self extinguishing material after adding flame retardant. Its softening point can be above 250 degrees Celsius and will only be decomposed at higher temperatures. In addition 20-year-old brand, the ash formed on the surface of polyurethane will be in its foam, and this ash will help isolate the foam below. It can effectively prevent the spread of fire. Moreover, polyurethane will not produce harmful gas at high temperature.
The three-dimensional automatic cold storage adopts computer, which can complete the loading and unloading, stacking, storage temperature and refrigeration equipment operation of the cold storage.
It is built in the room. There shall be excellent drainage pipe standards around the cold storage, the soil temperature shall be low, there shall be interlayer under the cold storage, and good natural ventilation shall be maintained. Maintaining dryness is very important for the cold storage. In addition, before the construction of the cold storage, the phase electricity of the relative volume shall be built according to the output power of the refrigeration unit. If the cold storage is water-cooled and radiating, the tap water pipeline shall be paved and the FRP cooling tower shall be built.
Rolando.According to the size and nature of the cold storage area and in combination with local regulations, the construction form of food cold storage warehouse is to determine the plane layout based on the site, whether it is a single-layer or double-layer warehouse, production process, refrigeration, product stacking, temperature, etc. are used to determine the size and location of the cold storage room, so that it can become a whole.
The floor of the cold storage shall be kept as close as possible during use
The overall construction achievements of the cold storage project have been put into use, and the service life can reach 10 years.